POWER UNIT ACCESSORIES

ETC system (Electronic Temperature Control)

ELECTRONIC ARRIVAL MANAGEMENT SYSTEM ON THE FLOOR

FOR NEW LIFTS AND RENOVATIONS INSTALLED ON LIFT EQUIPPED WITH A DISTRIBUTOR MOD. 3010

It reduces the energy consumption of the lift by up to 20% by optimizing the speed curves of approach (levelling) to the floor, resulting in a reduction in fly time and consequently in the engine insertion times.

In particular, the ETC system works on levelling spaces, reducing them and keeping them constant as temperature conditions change; It follows that the system travels for a longer time at full speed and then reduce the running time due to the levelling phases, where the engine is inserted, but the system works in low speed dissipating heat.

It also eliminates the use of valve and oil heating resistances, thus allowing additional energy savings.

At the same time, it ensures a traffic disposal capacity equivalent to a conventional hydraulic system with an average speed of 0.8 m/s.

The ETC system can also be installed on existing lifts without any changes to the system.

The installation of the ETC system on existing lifts can be realized in about 2 hours.

Once mounted, thanks to a temperature sensor detects the oil temperature, automatically learns the running and levelling times and, thanks to preset parameters, quickly adjusts itself in order to reduce levelling spaces in both rising and falling

The ETC system complies with the EN 81.20 standard as regards the stop of the cabin at the floor and the levelling accuracy of 10 mm

The 2CH system

The 2CH system was created following the general concept of safety of the lift, that is to have two control elements for each phase of operation of the lift

The 2CH system, applied to the 3010 circuit, ensures the control of the cabin descent through  two different valves.

This safety concept is already provided for by some regulations (e.g. Australia).

Soft Stop

The Soft Stop system is the result of constant GMV research aimed at achieving better and better performance for the hydraulic lift The innovations made to some components of the 3010 valve make it possible to apply this option also on existing lifts, making a small change to the control panel.

The advantages of this system are:

  • Absolute comfort when stopping rising;
  • Reduced noise during acceleration and deceleration and improved accuracy arrival on the floor.

These features make Soft Stop the ideal solution for prestigious lifts and buildings with great traffic that require excellent performance.

ACCESSORIES FOR 3010 EN VALVE

Hand pump

Component required by EN 81 and used for the following functions:

  • Emergency manoeuvre in rising
  • VC release (lock valve)

Maximum pressure switch

Component required by EN 81.

Inserted in the safety line, it allows to interrupt the power supply if the set pressure is exceeded.

Minimum pressure switch

Inserted in the safety line allows to stop the power supply when the pressure drops below that set (Preset: 5 Bar)

Low hysteresis pressure switches with load weighing device function

  • Type NO normally open contact
  • NC type with normally closed contact

Connected to an alarm, it allows to signal the overload in the cabin and therefore prevents the departure.

 

Pressure gauge with electrical contact

It performs the function of a pressure gauge together with the pressure switch of maximum and minimum.

 

Heating element valve 60W-230Vca

For the first morning travels, in cold environments, it helps to avoid overtravel phenomena due to the temperature or viscosity of the oil.

ACCESSORIES FOR 3010 EN POWER UNIT

Soft Starter

The Soft Starter extends the service life of the engine, ensuring:

  • Reduction of intensity peaks during start-up
  • Elimination of mechanical and electrical stress
  • Protection of the motor-pump unit
  • Decrease in electricity consumption
  • Starting noise reduction

The Soft Starter is recommended for high power lifts (over 18 kW).

.

 

Heating element in the tank – Possible supply voltage 400 – 230 Vca

For cold climates, it allows you to heat the oil and bring the viscosity within the parameters established for the smooth operation of the lifts, especially during the first morning rides. The resistance is equipped with internal thermostat not adjustable.

Microlevelling

Levelling device by means of motor unit /auxiliary pump of very low power. It saves energy and avoids frequent stresses to the main motor during the cabin relocation.

Recommended for goods passenger lifts and high capacity lifts. It reduces the electrical consumption of the lift and increases the accuracy at the stop for loading and unloading phases with pallets.